|
Post by msgoblue on Jan 2, 2014 8:59:11 GMT -8
Can anyone point me to a .6mm hex key or if there is another way to remove the set screw that holds the tail rotor shaft on? Im grounded until I can figure this out HELP ME PLEASE!!!
|
|
|
Post by PIC JND_old_No7 on Jan 8, 2014 10:46:49 GMT -8
I cannot help you as I am just starting. What I can say is that I am reconsidering if I want to get involved with Walkera because of the lack of support.
|
|
|
Post by msgoblue on Jan 8, 2014 15:12:41 GMT -8
This is the best site on the web when it comes to service dont even think to go somewhere else! I know as soon as they find the wrench it will be up on the web site,looks like the newer models have a phillips head instead of a hex.Don't give up you wont be sorry.
|
|
|
Post by msgoblue on Jan 25, 2014 5:49:55 GMT -8
Is there any possibility that the set screw size is a .05mm,that is the smallest size I have seen on line?
|
|
|
Post by PIC JND_old_No7 on Jan 25, 2014 8:57:00 GMT -8
Like I said, called the sales support line 949-943- 3599 4 days in a row. Never got a live person, never rec return call.
|
|
|
Post by msgoblue on Jan 26, 2014 6:49:33 GMT -8
I know I've sent two or three messages to the tech support same deal,no reply! I'm getting fed up with Walkera I was going to purchase a v120 but I'm having second thoughts may just save a bit longer and purchase an Align or a Blade,(the Master cp does make a good paperweight) Sorry Walkera.
|
|
|
Post by efvguy on Jan 30, 2014 10:29:23 GMT -8
Just had the same problem with them on a blade grip issue- no reply. So I solved my own problem. I found that a 1/16 hex is very close, and an apropriately sized jeweler's screwdriver will work too (which is what I actually used). Let me guess, the screw is really tight, right? It's probably installed with Loctite, just like the blade grip screws. I used a Weller 100W soldering gun, put the tip on the head of the screw, and heated for 10-15 secs. This will soften the Loctite enough to remove the screw. It will feel a little stiff, but it will come out. Clean up residual Loctite from the screw and hole, and use Loctite 242 for reinstall. Allow to cure overnight before use. Hope this helps. If you're interested in any further discussion on WHS, use my e-mail.
|
|
|
Post by msgoblue on Jan 30, 2014 16:11:54 GMT -8
Thanks for the input just so you know that the blade grip screws are a 1.5mm hex which should have come with the Mastercp,I need a .6mm very small the set screw is no bigger thana small tick, I just found a .7mm on line and ordered it I may have to sand it a bit but somehow I'll make it work . I'll keep you updated.
|
|
|
Post by efvguy on Jan 31, 2014 12:56:01 GMT -8
Thanks for the input as well. I will be waiting to hear how it turns out- no doubt I will need this knowledge one day!
|
|
|
Post by msgoblue on Feb 5, 2014 16:26:13 GMT -8
Got my wrenches today its not a.6 or a .7 it is a .9 finely an answer!! JUST GOOGLE MICRO TOOLS! now if I just didnt snap the motor wire(I'm a klutz sometimes)! I'll be ordering a new one tomorrow IT will be here by the weekend thanks to WHS
|
|